User Tools

Site Tools


le_preamp_series:le_preamp_series_user_s_manual

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
le_preamp_series:le_preamp_series_user_s_manual [2019/08/01 17:43]
dilan.hookoomsing [3.1 Side views]
le_preamp_series:le_preamp_series_user_s_manual [2019/08/01 17:46]
dilan.hookoomsing [5. Tips & tricks]
Line 260: Line 260:
   - **Before the first preamp**, we put all the effects we may want to apply to any Le Preamp in the chain. It could be a distortion pedal, a compressor, a volume pedal, anything you can put in front of an amplifier.   - **Before the first preamp**, we put all the effects we may want to apply to any Le Preamp in the chain. It could be a distortion pedal, a compressor, a volume pedal, anything you can put in front of an amplifier.
   - **In the FX loop** of each preamp, we put the effects we want to apply only to one of the preamps. For example, a specific delay we want only on Le Preamp 2.   - **In the FX loop** of each preamp, we put the effects we want to apply only to one of the preamps. For example, a specific delay we want only on Le Preamp 2.
-  - Finally, **after the last preamplifier**,​ we put all the global effects that are usually better sounding after the preamp stage: modulation or reverb effects, a speaker simulator such as the Torpedo C.A.B., and stereo effects. By placing the stereo effects at the end of the chain, the next device (mixer, stereo power amp, recorder etc...) can be fed by a stereo signal.+  - Finally, **after the last preamplifier**,​ we put all the global effects that are usually better sounding after the preamp stage: modulation or reverb effects, a speaker simulator such as the Torpedo C.A.B. ​M, and stereo effects. By placing the stereo effects at the end of the chain, the next device (mixer, stereo power amp, recorder etc...) can be fed by a stereo signal.
 ====== - Tips & tricks ====== ====== - Tips & tricks ======
  
-  * If you use a Torpedo C.A.B. with your Le Preamp, you may want to put the C.A.B. in the FX loop of Le Preamp. That way, you can connect the XLR DI output of Le Preamp to the mixer and listen ​ to the whole system, ​ including the Torpedo C.A.B. simulation, through Le Preamp’s headphones output.+  * If you use a Torpedo C.A.B. ​with your Le Preamp, you may want to put the C.A.B. ​in the FX loop of Le Preamp. That way, you can connect the XLR DI output of Le Preamp to the mixer and listen ​ to the whole system, ​ including the Torpedo C.A.B. ​simulation, through Le Preamp’s headphones output.
  
   * Even if it’s not shown on the connections diagram, you can use your Le Preamp like a "​simple"​ tube overdrive/​distortion. Just connect it in between your guitar/bass and your amplifier, like any pedal. If you take the time to carefully set the gain and volume of both channels on the preamp, you will be able to achieve amazing tones with your Le preamp!   * Even if it’s not shown on the connections diagram, you can use your Le Preamp like a "​simple"​ tube overdrive/​distortion. Just connect it in between your guitar/bass and your amplifier, like any pedal. If you take the time to carefully set the gain and volume of both channels on the preamp, you will be able to achieve amazing tones with your Le preamp!
le_preamp_series/le_preamp_series_user_s_manual.txt · Last modified: 2019/08/01 17:46 by dilan.hookoomsing